Differences

This shows you the differences between two versions of the page.

--- projects:3dprinting:anycubic_i3_mega:cura_bltouch_and_profile_settings [2020/02/22 23:25] – admin
+++ projects:3dprinting:anycubic_i3_mega:cura_bltouch_and_profile_settings [2020/10/30 01:09] (current) – admin
@@ Line 1: / Line 1: @@
+|  [[projects:3dprinting:anycubic_i3_mega | <- back to Anycubic I3 Mega modifications overview]]  |
 ===== Cura Machine settings for BLTouch =====
 Apart from adding the automatic BLTouch calibration before printing, there are many settings in Cura which affect printing quality. Keep in mind that even if BLTouch calibration is configured and executed correctly, printing quality may still be adverse due to other settings.
@@ Line 7: / Line 9: @@
   - Cura settings -> Printer -> Manage printers\\ \\ {{:projects:3dprinting:001.machine_settings_manage_printers.png?563×164}}\\ \\
   - Machine Settings\\ \\ {{:projects:3dprinting:002.machine_settings.settings_button.png?563x246}}\\ \\
-  - Place "G29 - Automatic Bed Leveling" under the last G28\\ \\ {{:projects:3dprinting:004.Machine_settings_settings.png?563x571}}
+  - Place "G29 - Automatic Bed Leveling" under the last G28((To save time and machine wear, enter "M420 S1 ; use last-saved matrix for leveling". Obviously the leveling measurements must have been done before and stored with the M500 command after performing leveling.))\\ \\ {{:projects:3dprinting:004.Machine_settings_settings.png?563x571}}
 ==== 2. Initial feed for sticking layer ====
@@ Line 27: / Line 29: @@
 ^ Quality  ^^^^^
 | //Layer Height//  | 0.10  | 0.10  | 0.15  |  mm  |
-| //Initial Layer Height//  | 0.10  | 0.10  | 0.2  |  mm  |
+| //Initial Layer Height//  | 0.10  | 0.10  | 0.10  |  mm  |
 | //Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
 | ..//Wall Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
@@ Line 34: / Line 36: @@
 | ..//Top/Bottom Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
 | ..//Infill Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
-| Initial Layer Line Width  | 140  | 140  | 140  |  %  |
+| Initial Layer Line Width  | 140  | 200  | 200  |  %  |
 ^ Shell ^^^^^
 | Wall Thickness  | 1.2  | 1.2  | 1.2  |  mm  |
@@ Line 74: / Line 76: @@
 | ..Support Speed  | 30  | 30  | 30  |  mm/s  |
 | Travel Speed  | 50  | 50  | 50  |  mm/s  |
-| //Initial Layer Speed//  | 25.0  | 20.0  | 20.0  |  mm/s  |
+| //Initial Layer Speed//  | 25.0  | 10.0  | 10.0  |  mm/s  |
 | Skirt/Brim Speed  | 40  | 40  | 40  |  mm/s  |
 | Enable Acceleration Control  | ✔  | ✔  | ✔  | |

Auditeon

User Tools

Site Tools

Differences

Page Tools