Auditeon

User Tools

Site Tools

Trace:
projects:3dprinting:anycubic_i3_mega:cura_bltouch_and_profile_settings

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
projects:3dprinting:anycubic_i3_mega:cura_bltouch_and_profile_settings [2020/03/08 21:40] – adminprojects:3dprinting:anycubic_i3_mega:cura_bltouch_and_profile_settings [2020/10/30 01:09] (current) – admin
Line 9: Line 9:
   - Cura settings -> Printer -> Manage printers\\ \\ {{:projects:3dprinting:001.machine_settings_manage_printers.png?563×164}}\\ \\    - Cura settings -> Printer -> Manage printers\\ \\ {{:projects:3dprinting:001.machine_settings_manage_printers.png?563×164}}\\ \\ 
   - Machine Settings\\ \\ {{:projects:3dprinting:002.machine_settings.settings_button.png?563x246}}\\ \\    - Machine Settings\\ \\ {{:projects:3dprinting:002.machine_settings.settings_button.png?563x246}}\\ \\ 
-  - Place "G29 - Automatic Bed Leveling" under the last G28\\ \\ {{:projects:3dprinting:004.Machine_settings_settings.png?563x571}}+  - Place "G29 - Automatic Bed Leveling" under the last G28((To save time and machine wear, enter "M420 S1 ; use last-saved matrix for leveling". Obviously the leveling measurements must have been done before and stored with the M500 command after performing leveling.))\\ \\ {{:projects:3dprinting:004.Machine_settings_settings.png?563x571}}
  
 ==== 2. Initial feed for sticking layer ==== ==== 2. Initial feed for sticking layer ====
Line 29: Line 29:
 ^ Quality  ^^^^^ ^ Quality  ^^^^^
 | //Layer Height//  | 0.10  | 0.10  | 0.15  |  mm  | | //Layer Height//  | 0.10  | 0.10  | 0.15  |  mm  |
-| //Initial Layer Height//  | 0.10  | 0.10  | 0.2  |  mm  |+| //Initial Layer Height//  | 0.10  | 0.10  | 0.10  |  mm  |
 | //Line Width//  | 0.40  | 0.35  | 0.35  |  mm  | | //Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
 | ..//Wall Line Width//  | 0.40  | 0.35  | 0.35  |  mm  | | ..//Wall Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
Line 36: Line 36:
 | ..//Top/Bottom Line Width//  | 0.40  | 0.35  | 0.35  |  mm  | | ..//Top/Bottom Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
 | ..//Infill Line Width//  | 0.40  | 0.35  | 0.35  |  mm  | | ..//Infill Line Width//  | 0.40  | 0.35  | 0.35  |  mm  |
-| Initial Layer Line Width  | 140  | 140  | 140  |  %  |+| Initial Layer Line Width  | 140  | 200  | 200  |  %  |
 ^ Shell ^^^^^ ^ Shell ^^^^^
 | Wall Thickness  | 1.2  | 1.2  | 1.2  |  mm  | | Wall Thickness  | 1.2  | 1.2  | 1.2  |  mm  |
Line 76: Line 76:
 | ..Support Speed  | 30  | 30  | 30  |  mm/s  | | ..Support Speed  | 30  | 30  | 30  |  mm/s  |
 | Travel Speed  | 50  | 50  | 50  |  mm/s  | | Travel Speed  | 50  | 50  | 50  |  mm/s  |
-| //Initial Layer Speed//  | 25.0  | 20.0  | 20.0  |  mm/s  |+| //Initial Layer Speed//  | 25.0  | 10.0  | 10.0  |  mm/s  |
 | Skirt/Brim Speed  | 40  | 40  | 40  |  mm/s  | | Skirt/Brim Speed  | 40  | 40  | 40  |  mm/s  |
 | Enable Acceleration Control  | ✔  | ✔  | ✔  | | | Enable Acceleration Control  | ✔  | ✔  | ✔  | |
projects/3dprinting/anycubic_i3_mega/cura_bltouch_and_profile_settings.1583700014.txt.gz · Last modified: 2020/03/08 21:40 by admin

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki