Differences

This shows you the differences between two versions of the page.

--- projects:3dprinting:anycubic_i3_mega:upgrade_kit [2020/03/04 13:23] – [Extruder intake] admin
+++ projects:3dprinting:anycubic_i3_mega:upgrade_kit [2020/03/08 21:40] (current) – admin
@@ Line 1: / Line 1: @@
+|  [[projects:3dprinting:anycubic_i3_mega | <- back to Anycubic I3 Mega modifications overview]]  |
 ====== Redrex extruder upgrade kit ======
 From the following [[https://www.amazon.co.uk/Redrex-Assembled-Extruder-Upgrading-Printers/dp/B07L9JJ7XJ|page]], an upgrade kit is offered, mainly containing a filament extruder motor with a gear reduction. The gear reduction would give the extruder more force to push the filament in.
@@ Line 24: / Line 26: @@
 ==== Extruder intake ====
-After following the [[https://github.com/davidramiro/Marlin-AI3M/wiki/Calibration#extruder-steps|extruder intake calibration procedure]] it was observed that instead of 100mm the intake was only 25mm, So this resulted into the following DEFAULT_AXIS_STEPS_PER_UNIT in Configuration.h:
+After following the [[https://github.com/davidramiro/Marlin-AI3M/wiki/Calibration#extruder-steps|extruder intake calibration procedure]] it was observed that instead of 100mm the intake was only 25mm((The reason for this is primarily that the stepper drivers are DRV8825 type and the steps/unit was still unchanged.)), So this resulted into the following DEFAULT_AXIS_STEPS_PER_UNIT in Configuration.h:
   //Old value: #define DEFAULT_AXIS_STEPS_PER_UNIT   { 160, 160, 800, 185.20 }
@@ Line 34: / Line 36: @@
   #define DEFAULT_AXIS_STEPS_PER_UNIT   { 160, 160, 800, E780.58 }
+For instructions, how to change the Configuration.h file, [[projects:3dprinting:anycubic_i3_mega_getting_and_adapting_firmware|please see here]].
 ==== Results ====
 With using the following test file:
-  * testfile
+  * {{ :projects:3dprinting:anycubic_i3_mega:test_10x10_5mm_hole.stl.zip | test_10x10_5mm_hole.stl.zip}}
 We were able to compare the print result with the original extruder motor and the Redrex gear reduction extruder motor (Bowden-type):
-^  Comparison Redrex vs. original  ^^
+^  Stringing comparison Redrex vs. original  ^^
 |  //First layer//  |  //Top layer//  |
 |  {{ :projects:3dprinting:anycubic_i3_mega:10x10x5_comparisonb.jpg?400}}  |  {{ :projects:3dprinting:anycubic_i3_mega:10x10x5_comparison.jpg?400}}  |
-The main differences are that the stringing/oozing plastic is much less with the Redrex gear reduction extruder motor.
+The main differences are that the stringing/oozing plastic is much less with the Redrex gear reduction extruder motor. The print result is substantially cleaner.
+The layer height with the Redrex extruder motor was reduced to 0.1mm. This height was not satisfactory to realize with the original extruder motor (which was 0.2mm). The difference can be seen with the following comparison:
+^  Layer comparison Redrex vs. original  ^
+|  {{ :projects:3dprinting:anycubic_i3_mega:10x10x5_comparisonc.jpg?400}}  |
 ==== Alternative extruder ====
-If other problems appear with filament not being able to pushed in, also the [[https://www.amazon.com/Zeelo-Extruder-Aluminum-Upgrade-Anycubic/dp/B07WFF3Z77|Zeelo dual drive extruder/motor]] could be a solution.
+  * If other problems appear with filament not being able to pushed in, also the [[https://www.amazon.com/Zeelo-Extruder-Aluminum-Upgrade-Anycubic/dp/B07WFF3Z77|Zeelo dual drive extruder/motor]] could be a solution.
+  * Or similarly built out of metal: [[https://www.aliexpress.com/item/32973962746.html]]

Auditeon

User Tools

Site Tools

Differences

Page Tools