projects:3dprinting:anycubic_i3_mega
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
projects:3dprinting:anycubic_i3_mega [2019/03/09 03:16] – [Hardware modification] admin | projects:3dprinting:anycubic_i3_mega [2020/11/03 00:05] – admin | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Modifications for the ANYCUBIC I3 MEGA 3d printer ====== | ====== Modifications for the ANYCUBIC I3 MEGA 3d printer ====== | ||
- | This page shows modifications | + | This page lists modification guides |
- | * How to retrofit the printer with a BLTouch leveler. | + | |
- | * Reverse engineer the distribution circuit board in order swap the external connectors for dsub-types. | + | |
- | ===== Retrofitting the printer with a BLTouch leveler | + | ===== Wiring modification guide ===== |
- | The printer can be upgraded with an automatic leveler from [[https:// | + | | |
- | ==== Hardware modification | + | ===== Antclaps BLTouch retrofit guide ===== |
- | The pins with which the BLTouch | + | Antclaps |
- | * D2 (Mega 2560, digital pin 2) for Zmin (Note that this signal has the label +X on the controller circuit board) | + | * [[projects: |
- | * D11 (Mega 2560, digital pin 11) for the control signal | + | * [[projects: |
+ | * [[projects: | ||
+ | * [[projects: | ||
+ | * [[projects: | ||
- | To understand how to connect the leveler to the controller, the following overview shows how the signals are routed (click on pictures for larger size): | + | * [[projects: |
- | ^ Anycubic I3 MEGA BLTouch wiring overview | + | |
- | | {{:projects: | + | |
- | With some larger pictures from the internal housing, the wiring looks like the following: | + | Further information |
- | ^ Anycubic I3 MEGA internal wiring details | + | |
- | | {{:projects: | + | |
- | + | ||
- | + | ||
- | To get the correct mounting position, a bracket was designed in freecad which fits close to the extruder: | + | |
- | ^ Bracket for BLTouch | + | |
- | | {{: | + | |
- | Please note that the shim which can be seen on the 2nd and 3rd picture was required in order to get a total distance of 25.0mm. The [[http:// | + | |
- | + | ||
- | At the print head a tiny strip board was added as carrier for a 3-pin jst connector. This would make it easier to separate the print head if necessary. Kapton tape was used to prevent any contact to adjacent pins. The square opening at the frame of the print head was made larger so the jst connector would also fit. Please note the difference between the last two pictures: | + | |
- | ^ Print head ^^^^ | + | |
- | | {{: | + | |
- | + | ||
- | The three wires for GND, +5v and control signal are added to the main cable assembly and routed via the side where the connectors are, into the inner housing: | + | |
- | ^ External wiring and final result | + | |
- | | {{: | + | |
- | + | ||
- | ==== Software modification ==== | + | |
- | Todo. See: [[http:// | + | |
- | ===== Distribution circuit board ===== | + | |
- | For easier upgrading mechanical parts of the printer, it would be beneficial to exchange the external connections to more robust and versatile DSUB type connectors. For this a new circuit board is required to replace the current board. | + | |
- | + | ||
- | In order to design this board, it is first necessary to reverse engineer the original circuit board: | + | |
- | + | ||
- | ^ Anycubic I3 MEGA distribution circuit board (with and without annotation) | + | |
- | | {{ : | + | |
- | | {{ : | + | |
- | + | ||
- | Click on either link above to find both sides of the circuit board | + |
projects/3dprinting/anycubic_i3_mega.txt · Last modified: 2020/11/09 01:16 by admin